Haltech E6GMX Manuel d'utilisateur Page 83
- Page / 114
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E6GMX Manual
83
Ignition Retard 0 – 20 °BTDC
The ECU will provide an ignition retard whenever the NOS
system is engaged.
Start-up Delay 0 – 120 s
The ECU will prevent the NOS system operating regardless of
the above conditions until the period of time programmed in
this field has elapsed.
11.12 Anti-Lag Switch
WARNING:
DO NOT OPERATE ANTI-LAG FOR PROLONGED PERIODS.
EXHAUST AND TURBO TEMPERTAURES RISE, WHICH MAY
CAUSE ENGINE DAMAGE.
The Anti-Lag switch function allows turbo-charged vehicles to decrease the “lag” associated
with boost when the motor is not under full load.
Retard Value 0 – 70 °BTDC
The ignition timing is retarded by this angle when the Anti-Lag
conditions for operation are met.
% Inc. Fuel 1 – 50 %
The percentage of fuel increased during Anti-Lag operation.
Zero TPS ONLY ON or OFF
If the Anti-Lag function is to be used when the Throttle Position
Sensor value is zero then turn this function ON.
Zero Inj Time 1 – 16 ms
If the zero TPS only function is ON then this value determines
the amount of fuel injected at zero or no throttle. The valid
range is (1-16) ms.
Throttle Perc. 5 – 80 %
The throttle position value below which Anti-Lag is
operational. The valid range is (5-80)%.
On RPM 100 – 16000 RPM
This field specifies the RPM above which Anti-Lag is
operational.
On Coolant Temp 0 – 127 °C / 32 - 261 °F
This field defines the coolant temperature above which Anti-
Lag is operational
The anti-lag system is can be enabled by a switch connected to Aux. In or by meeting all three
operating conditions stated above (the last 3 fields). Once the switch is enabled, if the
Throttle condition is met, the anti-lag system will be activated. The last two fields allow the
ALS to be activated when all three conditions are met regardless of the AUX In setting; this
allows the AUX In to be used for another purpose.
- Warnings 1
- Contents 2
- Introduction 7
- Before You Begin 8
- How It Works 10
- SECTION 1 Getting Started 11
- 1.2.4 Connect the ECU 12
- 2.1 Computer Requirements 13
- 2.2 Operating the Software 13
- 2.2.2 Running the Software 15
- 3.1 The Menu Structure 16
- 3.1.1 The File Menu 16
- 3.1.1.1 Load From File 17
- 3.1.1.2 Save To File 17
- 3.1.1.4 Quit 18
- 3.1.2 The Map Menu 19
- 3.1.2.2 Ignition Maps 20
- 3.1.2.3 Fuel Correction Maps 21
- 3.1.3 The Set-up Menu 22
- 3.1.4 The Options Menu 22
- 3.1.5 Data Page Menu 22
- 3.1.6 Password Protection 23
- 3.2.1 Going Online 24
- 3.3 Hot Key Summary 26
- 4.2 The ECU Set-up Pages 27
- 4.2.1 Main Set-up Page 27
- 4.2.2 Fuel Set-up Page 29
- 4.2.3 Ignition Set-up Page 32
- 4.2.4 Trigger Setup 34
- 4.2.5 The In/Out Set-up Page 35
- HALTECH MAPS 38
- 4.3 What are Maps? 38
- 4.4.2 All Ranges 40
- 4.4.3 Percentage Changes 40
- 4.4.4 Linearise 41
- 4.4.5 Numeric Mode 43
- 4.4.6 3D View 44
- 4.5 The Haltech Maps 45
- 4.5.3 Fuel Correction Map 45
- 4.5.5 Zero Throttle Map 47
- 4.5.6 Full Throttle Map 47
- 4.5.7 Turbo Waste-gate Maps 48
- 4.6 Dual Maps 48
- 4.6.1 Editing Dual Maps 49
- SECTION2 Tuning The Engine 50
- 5.5.4 Tuning for Idle 53
- 5.5.5 Tuning with No Load 53
- 5.5.6 Loading the Engine 53
- 5.5.7 Fine Tuning the Engine 54
- CHAPTER 6 THROTTLE EFFECTS 55
- 6.1 Throttle Response 55
- 6.2 Zero Throttle Map 56
- 6.3 Full Throttle Map 56
- 7.1 Cold Cranking 57
- 8.1 Fuel Versus Air Temp Map 58
- 8.2 The Battery Voltage Map 58
- 8.3 The Ignition Coolant Map 58
- 8.5 Barometric Correction 59
- 8.6 Post Start Enrichment 62
- SECTION 3 Software Features 63
- 9.1.3 Logging the Data 64
- 9.1.4 Displaying The Data 65
- 9.1.4.1 Displaying Channels 66
- 9.1.4.4 Removing A Dataset 67
- 9.1.4.5 Data Values 68
- 9.1.4.6 Zooming 68
- 10.1 Idle Speed Control and O 72
- Closed Loop Control 72
- 10.1.1 Idle Control 72
- 10.2 The PWM Options Page 76
- 11.10 Turbo Timer (TT) 82
- 11.11 NOS Switch 82
- 11.12 Anti-Lag Switch 83
- 11.13 Air Conditioning 84
- 11.14 Engine Control Relay 84
- 11.15 VTEC 85
- 11.16 BAC2 85
- 11.18 TPS Switch 86
- SECTION 5 Appendices 88
- A.1 Control Program Problems 89
- A.3 Starting problems 90
- A.4 Idling Problems 90
- A.6 Full Power Problems 91
- A.8 Cold Running Problems 91
- A.9 Fuel Consumption 91
- Ignition 92
- B.7 Ignition Outputs 93
- Constant Duty 93
- Constant Charge 94
- APPENDIX C INJECTORS 100
- C.1 Injector Impedance 100
- C.2 The Injector Drivers 101
- APPENDIX D FUEL SYSTEMS 102
- D.1 Duty Cycles 102
- D.2 Fuel Requirement 104
- D.3 Injector Flow Capacity 104
- D.4 Fuel Pump Capacity 105
- E.1 Trigger Edge 106
- E.2 Trigger Angle 108
- E.3 Trigger Pull up 109
- E6GMX Manual 113
- E6GMX Hardware Options 113
- LIMITED WARRANTY 114
Produits connexes et manuels pour Pour la voiture Haltech E6GMX
Pour la voiture Haltech E6M Manuel d'utilisateur
(152 pages)
(152 pages)
Pour la voiture Haltech E6K Manuel d'utilisateur
(154 pages)
(154 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.567 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels