Haltech E6GMX Manuel d'utilisateur Page 17
- Page / 114
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E6GMX Manual
17
3.1.1.1 Load From File
Load From File allows the user to load a file that contains all the “set-up” and “map” data the
ECU requires to run a particular engine. This file has been saved during a previous tuning
session when the programming PC was connected to the ECU. When the ECU is “Offline”,
the Load Map function can be used to load the information from an E6GMX map file
(denoted by the .6XM file extension) into the front-end software to view its contents. If the
ECU is “Online” using the Load Map function will cause the ECU to be loaded with the
information stored in the file and all information previously stored in the ECU will be lost.
NOTE:
When using the load function be aware that when the ECU is online all “set-
up” and “map” data currently stored in the ECU will be overwritten.
To choose the desired map simply select the desired file from the dialog and press enter. This
is illustrated below,
The selected filename will be displayed in the horizontal black bar below the text “Opening
File”:
Press Enter
When the ECU is “Online” the central Status Bar will turn red and indicate the load status of
the map.
3.1.1.2 Save To File
The ECU programming software allows the user to save all the information in the ECU to a
file on the programming PC. This allows the user to save a map and continue tuning and
then, if required, revert to a previous map.
- Warnings 1
- Contents 2
- Introduction 7
- Before You Begin 8
- How It Works 10
- SECTION 1 Getting Started 11
- 1.2.4 Connect the ECU 12
- 2.1 Computer Requirements 13
- 2.2 Operating the Software 13
- 2.2.2 Running the Software 15
- 3.1 The Menu Structure 16
- 3.1.1 The File Menu 16
- 3.1.1.1 Load From File 17
- 3.1.1.2 Save To File 17
- 3.1.1.4 Quit 18
- 3.1.2 The Map Menu 19
- 3.1.2.2 Ignition Maps 20
- 3.1.2.3 Fuel Correction Maps 21
- 3.1.3 The Set-up Menu 22
- 3.1.4 The Options Menu 22
- 3.1.5 Data Page Menu 22
- 3.1.6 Password Protection 23
- 3.2.1 Going Online 24
- 3.3 Hot Key Summary 26
- 4.2 The ECU Set-up Pages 27
- 4.2.1 Main Set-up Page 27
- 4.2.2 Fuel Set-up Page 29
- 4.2.3 Ignition Set-up Page 32
- 4.2.4 Trigger Setup 34
- 4.2.5 The In/Out Set-up Page 35
- HALTECH MAPS 38
- 4.3 What are Maps? 38
- 4.4.2 All Ranges 40
- 4.4.3 Percentage Changes 40
- 4.4.4 Linearise 41
- 4.4.5 Numeric Mode 43
- 4.4.6 3D View 44
- 4.5 The Haltech Maps 45
- 4.5.3 Fuel Correction Map 45
- 4.5.5 Zero Throttle Map 47
- 4.5.6 Full Throttle Map 47
- 4.5.7 Turbo Waste-gate Maps 48
- 4.6 Dual Maps 48
- 4.6.1 Editing Dual Maps 49
- SECTION2 Tuning The Engine 50
- 5.5.4 Tuning for Idle 53
- 5.5.5 Tuning with No Load 53
- 5.5.6 Loading the Engine 53
- 5.5.7 Fine Tuning the Engine 54
- CHAPTER 6 THROTTLE EFFECTS 55
- 6.1 Throttle Response 55
- 6.2 Zero Throttle Map 56
- 6.3 Full Throttle Map 56
- 7.1 Cold Cranking 57
- 8.1 Fuel Versus Air Temp Map 58
- 8.2 The Battery Voltage Map 58
- 8.3 The Ignition Coolant Map 58
- 8.5 Barometric Correction 59
- 8.6 Post Start Enrichment 62
- SECTION 3 Software Features 63
- 9.1.3 Logging the Data 64
- 9.1.4 Displaying The Data 65
- 9.1.4.1 Displaying Channels 66
- 9.1.4.4 Removing A Dataset 67
- 9.1.4.5 Data Values 68
- 9.1.4.6 Zooming 68
- 10.1 Idle Speed Control and O 72
- Closed Loop Control 72
- 10.1.1 Idle Control 72
- 10.2 The PWM Options Page 76
- 11.10 Turbo Timer (TT) 82
- 11.11 NOS Switch 82
- 11.12 Anti-Lag Switch 83
- 11.13 Air Conditioning 84
- 11.14 Engine Control Relay 84
- 11.15 VTEC 85
- 11.16 BAC2 85
- 11.18 TPS Switch 86
- SECTION 5 Appendices 88
- A.1 Control Program Problems 89
- A.3 Starting problems 90
- A.4 Idling Problems 90
- A.6 Full Power Problems 91
- A.8 Cold Running Problems 91
- A.9 Fuel Consumption 91
- Ignition 92
- B.7 Ignition Outputs 93
- Constant Duty 93
- Constant Charge 94
- APPENDIX C INJECTORS 100
- C.1 Injector Impedance 100
- C.2 The Injector Drivers 101
- APPENDIX D FUEL SYSTEMS 102
- D.1 Duty Cycles 102
- D.2 Fuel Requirement 104
- D.3 Injector Flow Capacity 104
- D.4 Fuel Pump Capacity 105
- E.1 Trigger Edge 106
- E.2 Trigger Angle 108
- E.3 Trigger Pull up 109
- E6GMX Manual 113
- E6GMX Hardware Options 113
- LIMITED WARRANTY 114
Produits connexes et manuels pour Pour la voiture Haltech E6GMX
Pour la voiture Haltech E6M Manuel d'utilisateur
(152 pages)
(152 pages)
Pour la voiture Haltech E6K Manuel d'utilisateur
(154 pages)
(154 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.976 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels